Right here in the next paragraph you can find a good deal of awesome expertise pertaining to A Step-by-Step Guide to Installing a Bathtub.
Installing a bathtub isn't exactly brain surgery, however it does call for solid plumbing, carpentry, and in some cases, tiling skills. Replacing an old tub with a brand-new one is likewise a reasonably challenging job. If the old tub is readily accessible, the project can relocate speedily; if you need to open up a wall surface to get rid of the old bathtub and also place the brand-new tub, the job is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will certainly require an assistant to leave the old bathtub as well as set in the brand-new one. Make certain you have actually qualified yourself for the job and are comfortable attempting it. As opposed to working with a specialist to take over a halfway-completed task, it is much better to consider using one prior to you begin. Chances are you may require an expert plumber to make tube connections.
This short article will aid you set up a new bathtub in your bathroom if you have actually already bought a brand-new bathtub as well as don't require to alter the arrangement of your previous water system pipes.
Your devices and material checklist ought to comprise the following:
Getting ready for the Installation
To start with, the sustaining framework supplied with the bath needs to be fitted (if needed) according to the manufacturer's guidelines. Next off, fit the faucets or mixer to the tub. When fitting the faucet block, it is necessary to make sure that if the faucet includes a plastic washer, it is fitted in between the bath and the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the faucets unit to stop stress on the bathtub.
Fit the adaptable tap adapters to the bottom of the two taps making use of 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet through the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Ensure you utilize every one of the supplied washers.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom should now prepare to be suited its final position.
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your installment, then the first thing you must do is separate the supply of water. After doing so, switch on the faucets to drain pipes any water staying in the system. The procedure of getting rid of the existing taps can be quite bothersome due to the limited accessibility that is often the case.
Use a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the taps. Have a cloth ready for the staying water that will come from the pipes. When the supply pipelines have actually been gotten rid of, make use of the very same device to loosen the nut that holds the taps onto the bath/basin. You will need to stop the solitary faucets from transforming throughout this procedure. Once the taps have been removed, the holes in the bath/basin will have to be cleaned of any old sealing compound.
Prior to going on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the brand-new faucets to fit.
Setting up the Tub
Utilizing both wooden boards under its feet, put the tub in the required position. The wooden boards are helpful in equally spreading out the weight of the tub over the area of the boards instead of concentrating all the weight onto 4 tiny factors.
The next goal is to guarantee that the bath tub is leveled all round. This can be attained by examining the level as well as changing the feet on the tub until the spirit level reads degree.
To mount faucets, fit the bottom of the furthest adaptable tap adapter to the proper supply pipeline by making a compression sign up with; then do the exact same for the other tap.
Switch on the water supply and examine all joints and also brand-new pipework for leakages and also tighten them if necessary. Fill up the tub and also examine the overflow electrical outlet and also the typical outlet for leaks.
Finally, take care of the bath paneling as described in the supplier's user's manual. Tiling as well as sealing around the bathtub needs to wait till the bath tub has actually been utilized at least when as this will resolve it into its last setting.
Fitting New Touches
If the tails of the new faucets are plastic, then you will require a plastic connector to stop damage to the string. One end of the port fits on the plastic tail of the faucet and also the various other end supplies a connection to the existent supply pipelines.
If you require to fit a monobloc, after that you will require reducing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, position the tap in the placing opening in the bath/basin making sure that the washers remain in location between the tap and also the sink. Protect the tap in position with the producer provided backnut. As soon as the faucet is securely in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with typical tap connectors. The previous type needs to be linked to the tap finishes first, tightening up only by hand. The supply pipelines can later be linked to the other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the location where the bath fulfills the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is essential as the installation can move sufficient to crack an inflexible seal, creating the water to penetrate the wall surface between the bath and also the tiling, resulting in issues with dampness as well as feasible leaks to the ceiling listed below.
You can choose from a range of coloured sealants to assimilate your fixtures as well as installations. They are sold in tubes as well as cartridges, and also are capable of sealing gaps as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with spins of drenched paper or soft rope. Remember to always fill up the bath tub with water prior to sealing, to enable the motion experienced when the bathtub is in usage. The sealer can fracture fairly very early if you do not take into account this movement prior to securing.
Additionally, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are additionally easily available on the marketplace. It is suggested to fit the tiles using water-resistant or water resistant glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I stumbled upon that review on How to Install a Bathtub Yourself when doing a lookup on the search engines. Sharing is caring. You won't know, you may just be helping someone out. I am grateful for your time. Visit us again soon.
Additional Resources